With ProCalV5’s Test Type Packages, different "Test Types" may be applied to any item master record whose required calibration does not fit perfectly into the standard ProCalV5 template. Test Types may be used to provide specific testing in addition to or instead of a standard calibration with target set points and as found/as left readings. The Test Type package does all calculations automatically, and determines the pass/fail of the calibration with completely separate logical functionality.
Examples of some calibration test types that ProCal V5 normally could not accommodate efficiently are extreme values, linearity, and standard deviation tests. These tests are not dependent on the readings of each point, but more on the combination of all readings and some additional values. If the package you require has not already been created, our programmers will be happy to custom design a package to fit your needs.
Test Type Package highlights include;
- Custom Test Type Package algorithms can be designed to suit any requirement regardless of the complexity
- Useful for HPLC, Spectrophotometer and other laboratory devices
- Create any type of special testing for power, electrical, and other equipment & systems
- Any formulaic calculations can be performed on your entered data, i.e. mean, reproducibility, standard deviation, linearity and more
- Custom reports can be developed to each test to match your exact specifications
- Libraries of existing test sets are available
Test Type Package Library includes…
Air Particle Counter Test
Test Type Package This test verifies the ability of Air Particle Counters to count particles of various sizes.
Air Sampler 1
Test Type Package for testing aspirated volume & recording K3 factor with a MAS-100C calibrator.
Air Sampler 2
Test Type Package designed to test aspirated volume & record K3 & K5 factor with a DA-100 calibrator.
Air Sampler 3
Test Type Package for testing differential pressure by looking up related flow value in table.
Billing Information
This Test Type Package provides the user with the ability to enter billing information directly into ProCalV5 including list of Part Numbers, Descriptions & Costs
Biocontainment Cabinet
This TTP performs a test for Downflow Velocity, Inflow Velocity, HEPA Filter Integrity, as well as, performance tests for Cabinet Integrity, Air Flow Smoke Pattern, Site Installation Assessment, and Electrical Tests.
Bio Safety Cabinet
This TTP allows users to certify Bio Safety Cabinets. On the visual prompt provided in ProCalV5, users can record Downflow Velocity, Test Method, HEPA Filter Integrity, Air Flow Smoke and an Acceptance Criteria. Pass/fail is determined by HEPA Integrity Result, Smoke Test Downflow Uniformity, Smoke Test Containment, Smoke Test Opening Containment, Downflow Velocity Average (Standard Test), Back, Middle and Front Velocity Averages (Zoned Test) and Intake Velocity Average.
Calibration Codes
The Calibration Codes Test Type Package performs normal ProCalV5 calibration calculations and then assigns a letter A, B, C, or D as the output based on the results
Chart Recorder Test
Test Type Package designed to test the accuracy of the timing functionality of a chart recorder.
Dissolution – Chemistry
The Dissolution - Chemistry provides for Tablet Calibration test portion of Dissolution Bath calibrations. This TTP results in the eventual comparison of a “% Dissolved” value for each vessel, compared to the minimum and maximum % Dissolved based on a USP Lot number.
Dissolution – Temperature
The Dissolution - Temperature allows the user to capture a given number of temperature test points, each one representing a vessel in a Dissolution Bath, or an External Bath, or some Other Probe related to the test.
Dissolution – Wobble
The Dissolution – Wobble Test Type Package allows the user to capture the Apparatus used when performing Dissolution Wobble tests of several vessels of a Dissolution Bath.
Divisions Verification – Force Calibration
The Divisions Verification Test Type Package interpolates intermediary values of the output signal type between test readings, based on the difference of those test readings divided by the difference in the input set points.
Extreme Values Test
The Extreme Values Test Type Package accepts a set of test point inputs and calculates the minimum or maximum reading from the set
Fume Hood Certification
This Test Type Package allows users to certify fume hoods. User set the Output Resolution and the Acceptable Low & High Values. Also, a user can set the # of Columns, # of Rows, Sash Opening and Sash Width. During a calibration is where the Average Velocity, Hood Opening, and Air Volume are calculated and the Pass/Fail is based upon the average velocity compared to a user established acceptable specified range.
Gage R&R Utility
The ProCalV5 Gage R&R Utility allows users to collect data for a Gage Repeatability and Reproducibility study on individual items they are managing and report on range of operators, acceptability and more.
Glove Box Certification
This powerful Test Type Package will allow users to perform glove box certifications. Box Height and Sash Width for the glove box are managed in ProCalV5 and assigned by asset. The visual prompt for performing calibrations allows users to perform a calibration/certification to their Glove Box.
HEPA Filter Integrity Check
The HEPA Filter Integrity Test Type Package will summarize the results for HEPA Filter Integrity tests (in VLF mode) and apply a pass/fail to the data. The test will calculate the Average Face Velocity = Mean of all the entered Velocity Data entered in any preceding test point groups that use the “VLF” “Test Type” input value and determine pass/fail based on the Low Velocity & High Velocity calibration points.
HPLC Pump Flow Rate
The HPLC Pump Flow Rate Test Type Package provides capability for using a Flow Meter, a Class A Buret, or a Volumetric Flask to calibrate the Flow Rate of a HPLC Pump
HPLC Pump Gradient Proportioning
The HPLC Pump Gradient Proportioning Test Type Package provides capability for determining the percent flow contribution from several channels of a HPLC Pump
HPLC Autosampler
The HPLC Autosampler Test Type Package involves the gathering of two vial weight readings from a HPLC Autosampler to be compared to some expected weight change within a tolerance specified as Pct of Reading
HPLC Extreme Values Test
The Extreme Values Test Type Package accepts a set of test point inputs and calculates the minimum or maximum reading from the set from the results of the HPLC Detector.
Input Conversion Test
This Test Type Package will allow users to display the As Found and As Left readings back in the unit of the Input Signal Type in ProCalV5. This test defaults to a linear correlation from Input Range to Output Range unless the Correlation to Output is specifically set to Square Root by a user.
Laminar HEPA Filter Test
The Laminar HEPA Filter Test Type Package calculates the Average Flow and a limit based on that Average Flow across a HEPA Filter from a set of flow measurements.
Linearity Test
The Linearity Test Type Package calculates a correlation coefficient and its square from a set of inputs and readings and compares them against a standard of acceptance
Manual Pass/Fail
The Manual Pass/Fail Test Type Package allows the user to identify the test using the Group Name field, and enter whether or not it passed or failed.
Metric Weights Test (Standard Deviation)
This Test Type Package tests average differential and calculates average weight & Mean Standard Deviation
Monitor Mark/Freeze Watch
Test Type Packages for two tests designed at two different temperatures for a time period.
PE 900 Series Interface
The PE 900 Series Interface Test Type Package captures three values for each of two Channels (A and B): Percent Gain, SD Gain Error and Linearity Error according to a +/- deviation from zero Tolerance specification.
Pipette Calibration
This allows users to capture multiple repeated volumes and weights per each Pipette test volume. Each set of readings is tested for precision (%RSD) and Accuracy (% of target volume).
Pipette Calibration (Z-Factor)
This allows users to capture multiple repeated weights per each Pipette test volume, and convert to the corresponding volume according to an entered temperature value.
Pipette Calibration with Conversion
This test type allows users to capture multiple repeated weights per each Pipette test volume, and convert to the corresponding volume according to an entered temperature value. This is done using a water density factor table. Conversion from milliliter and micro liter to milligrams or grams is done automatically. Each set of readings is tested for precision (%RSD) and Accuracy (% of target volume).
Reproducibility
The Reproducibility Test Type Package calculates the Standard Deviation and Reproducibility value for the given test group, for a variable number of readings, a standard value, and a maximum Reproducibility value. It then compares the Reproducibility to the maximum Reproducibility value to determine the Pass/Fail.
RTD Curve Test
Temperature-to-Ohms conversion in Celsius and Fahrenheit, lookup or interpolate Inputs from Outputs or Outputs from Inputs, from Temperature to Ohms and Ohms to Temperature.
Scales & Balances Test
This powerful Test Type Package provides calculation of scales & balance calibrations for multiple tests including Zero tests, Corner Tests & Repeatability tests.
SMA Sampler
This Test Type Package will perform Pass/Fail on a Velocity Reading and a Time reading, in fractional Minutes. It will also give a Replace Battery warning when the Average Voltage of a set of test point readings is outside of a given acceptable range.
Stopwatch Test
The Stopwatch Test Test Type Package calculates the Deviation, % Deviation and % Error for a Stopwatch based on a specified standard frequency and a reading of a measured frequency.
Switch Test
The Switch Test allows the user to capture either a single point trip test or a two-point trip and reset test. Many of the features of ProCalV5’s standard calibration are used, such as the variety of limit calculations and providing the ramp range. A special feature of this Test Type package is the ability to download this test to a Field Calibrator using the ProCalV5 Field Calibrator Utility FCINTF interface.
Tablet Press
The Tablet Press calculates a Tab / Hr * 1000 value for a number Tablet Press stations and compares it to the indicated Tab / Hr * 1000 value.
Task List
This Test Type Package will supply and record a list of tasks for maintenance or calibration-related maintenance steps to be recorded on a Calibration record.
Template Group Load
Template Group Load Test Type Package will allow users to load a test point group from a different item dynamically during calibration entry. This allows certain items to be used as “templates” for groups in another item. Optionally, only a certain number of points will be taken from the requested item/test point group as well.
Test Omission
The Test Omission Test Type Package allows the user to omit particular test group(s) from the overall determination of Calibration Pass/Fail.
Timer Test
The Timer Test Test Type Package allows the user to capture and automatically process and calculate time measurements to be compared with some target time
Uncertainty Calculations
This feature uses Test Type Package (TTP) functionality to perform an Uncertainty Budget Calculation when an item is calibrated if the User has assigned the appropriate standards. The TTP calculates an Expanded Uncertainty value for a given unit, Coverage Factor (k) and desired number of significant figures.
Our list is always growing, so feel free to bookmark this page to
see what else is available to your ProCalV5 product!
To Request More Information Click Here!
